Tuesday, 30 April 2013
Making High Quality iPod iPhone Speakers
This top of the range and low value speaker used to be designed for use for iPod or iPhone with using old automobile Hi-Fi speaker and some pc parts. Other materials used are proven in the picture below they usually include an amplifier, 240V-12V energy supply, tweeters, crossovers, sealed lead acid battery, MDF, filler, Apple common dock & faraway, glue, nails, and white gloss paint.
The front baffle board used to be drawn on a piece of MDF in an effort to use it as a template to make the rear of the box. The dimensions of the box primarily based on the speaker do not essentially want to be precise since the audio system have been relatively old because it comes from an old Renault 19.
From the photo of the spherical bits beneath, the trusty round saw was used to minimize a selection of 1 inch by using 15 cm strips of MDF. Between the entrance and rear baffle, the strips have been glued and nailed. The baffles were cut out using a jigsaw and the strips had been saved as close to one another as possible.
The first coat of filler can take 3 batches to complete and they had been applied as neatly as it may just after being blended up. Until it was once someplace close to as proven under, a couple of more coats can be utilized. A surform shall be utilized until it was as soon as about the precise shape once the primary coat of filler had set. Sanding could be finished by using hand or it would be higher to use an electric sander if available. A jigsaw was as quickly as used to lower out the speaker and tweeter gaps as proven below and a flange for the speaker to sit into used to be made utilizing the router.
A gap of about 12mm on the highest and 3mm on the again were drilled as quickly as the entire holes were cut. The parts have been masked up and the baffle was spray painted in matt black as proven below. The first layer of white primer can be utilized as soon as the black used to be dry and the masking tape used to be eliminated. A couple of coats of regular white primer was applied after which followed with the support of a light sand. In between, a bit of sanding used to be applied as three coats of white gloss were given.
A grill for the entrance had to be made for the entire pretend Apple. To mark out the form on a scrap little bit of 5mm laminate ground, this was once a easy matter of utilizing the box as a template and then sprayed it in matt black. Some black nylon material used to be glued onto the panel with some spray carpet adhesive when the paint was once dry as proven in the image below.
Some black drywall screws had been used to screw the 13cm speaker into the field in addition to the amp and crossover communitys and epoxy resin was once used to glue the tweeters. After soldering all of the connections, the lead acid battery used to be glued within as shown within the subsequent picture. The amp of the battery was once energyed by using wiring the 12V to the battery. The iPod universal dock was glued on the highest of the field with wires for USB and audio. The finished product of cool having a look iPod speaker can be proven under.
The front baffle board used to be drawn on a piece of MDF in an effort to use it as a template to make the rear of the box. The dimensions of the box primarily based on the speaker do not essentially want to be precise since the audio system have been relatively old because it comes from an old Renault 19.
From the photo of the spherical bits beneath, the trusty round saw was used to minimize a selection of 1 inch by using 15 cm strips of MDF. Between the entrance and rear baffle, the strips have been glued and nailed. The baffles were cut out using a jigsaw and the strips had been saved as close to one another as possible.
The first coat of filler can take 3 batches to complete and they had been applied as neatly as it may just after being blended up. Until it was once someplace close to as proven under, a couple of more coats can be utilized. A surform shall be utilized until it was as soon as about the precise shape once the primary coat of filler had set. Sanding could be finished by using hand or it would be higher to use an electric sander if available. A jigsaw was as quickly as used to lower out the speaker and tweeter gaps as proven below and a flange for the speaker to sit into used to be made utilizing the router.
A gap of about 12mm on the highest and 3mm on the again were drilled as quickly as the entire holes were cut. The parts have been masked up and the baffle was spray painted in matt black as proven below. The first layer of white primer can be utilized as soon as the black used to be dry and the masking tape used to be eliminated. A couple of coats of regular white primer was applied after which followed with the support of a light sand. In between, a bit of sanding used to be applied as three coats of white gloss were given.
A grill for the entrance had to be made for the entire pretend Apple. To mark out the form on a scrap little bit of 5mm laminate ground, this was once a easy matter of utilizing the box as a template and then sprayed it in matt black. Some black nylon material used to be glued onto the panel with some spray carpet adhesive when the paint was once dry as proven in the image below.
Some black drywall screws had been used to screw the 13cm speaker into the field in addition to the amp and crossover communitys and epoxy resin was once used to glue the tweeters. After soldering all of the connections, the lead acid battery used to be glued within as shown within the subsequent picture. The amp of the battery was once energyed by using wiring the 12V to the battery. The iPod universal dock was glued on the highest of the field with wires for USB and audio. The finished product of cool having a look iPod speaker can be proven under.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment
Note: only a member of this blog may post a comment.