Showing posts with label alarm. Show all posts
Showing posts with label alarm. Show all posts
Friday, 19 September 2014
Burglar Alarm With Timed Shutoff Circuit Diagram
This is a Burglar Alarm With Timed Shutoff Circuit Diagram. When SI (sensor) is closed, power is applied to U2, a dual timer. After a time determined by C2, CI is energized after a predetermined time determined by the value of C5, pin 9 of U2 becomes low, switching off the transistor in the optoisolater, cutting anode current of SCR1 and DE-energizing Kl. The system is now reset. Notice that (i6x C2) is less than (R7xC$). The ON time is approximately given by:(R7xC5)-(R6xC2) = Ton
Burglar Alarm With Timed Shutoff Circuit Diagram
Friday, 12 April 2013
Simple Shadow Detector Alarm
This is also known as Sun up alarm, in this circuit you can set the LDR’s sensitivity by 100k potentiometer, you can set it with any lamp around your room (tube light, bulb, LED etc) by varrying the 100k potentiometer. We can also control the buzzer time by 1M potentiometer
You can Enhance this project and set the sensitivity of the LDR with a lazer light and keep it on the way of any door circuit at one side and lazer at other side of the door and a then you can make this project to buzz as soon as some one enters in a room
I personally set this project in my room with sensitivity of tube light and whenever i came in and turn my room’s tube light on
rookieelectronics
Circuit Diagram:
You can Enhance this project and set the sensitivity of the LDR with a lazer light and keep it on the way of any door circuit at one side and lazer at other side of the door and a then you can make this project to buzz as soon as some one enters in a room
I personally set this project in my room with sensitivity of tube light and whenever i came in and turn my room’s tube light on
rookieelectronics
Parts Required:
|
Thursday, 11 April 2013
Automatic Night Lamp with Morning Alarm
This circuit automatically turns on a night lamp when bedroom light is switched off. The lamp remains ‘on’ until the light sensor senses daylight in the morning. A super-bright white LED is used as the night lamp. It gives bright and cool light in the room. When the sensor detects the daylight in the morning, a melodious morning alarm sounds. The circuit is powered from a standard 0-9V transformer. Diodes D1 through D4 rectify the AC voltage and the resulting DC voltage is smoothed by C1. Regulator IC 7806 gives regulated 6V DC to the circuit. A battery backup is provided to power the circuit when mains fails. When mains supply is available, the 9V rechargeable battery charges via diode D5 and resistor R1 with a reasonably constant current. In the event of mains failure, the battery automatically takes up the load without any delay. Diode D5 prevents the battery from discharging backwards following the mains failure and diode D6 provides current path from the battery.
Automatic Night Lamp with Morning Alarm Circuit Diagram
The circuit utilises light-dependant resistors (LDRs) for sensing darkness and light in the room. The resistance of LDR is very high in darkness, which reduces to minimum when LDR is fully illuminated. LDR1 detects darkness, while LDR2 detects light in the morning. The circuit is designed around the popular timer IC NE555 (IC2), which is configured as a monostable. IC2 is activated by a low pulse applied to its trigger pin 2. Once triggered, output pin 3 of IC2 goes high and remains in that position until IC2 is triggered again at its pin 2. When LDR1 is illuminated with ambient light in the room, its resistance remains low, which keeps trigger pin 2 of IC2 at a positive potential. As a result, output pin 3 of IC2 goes low and the white LED remains off. As the illumination of LDR1’s sensitive window reduces, the resistance of the device increases.
In total darkness, the specified LDR has a resistance in excess of 280 kilo-ohms. When the resistance of LDR1 increases, a short pulse is applied to trigger pin 2 of IC2 via resistor R2 (150 kilo-ohms). This activates the monostable and its output goes high, causing the white LED to glow. Low-value capacitor C2 maintains the monostable for continuous operation, eliminating the timer effect. By increasing the value of C2, the ‘on’ time of the white LED can be adjusted to a predetermined time. LDR2 and associated components generate the morning alarm at dawn. LDR2 detects the ambient light in the room at sunrise and its resistance gradually falls and transistor T1 starts conducting. When T1 conducts, melody-generator IC UM66 (IC3) gets supply voltage from the emitter of T1 and it starts producing the melody. The musical tone generated by IC3 is standard 0-9V transformer. Diodes D1 through D4 rectify the AC voltage and the resulting DC voltage is smoothed by C1. Regulator IC 7806 gives regulated 6V DC to the circuit.
A battery backup is provided to power the circuit when mains fails. When mains supply is available, the 9V rechargeable battery charges via diode D5 and resistor R1 with a reasonably constant current. In the event of mains failure, the battery automatically takes up the load without any delay. Diode D5 prevents the battery from discharging backwards following the mains failure and diode D6 provides current path from the battery.
The circuit utilises light-dependant resistors (LDRs) for sensing darkness and light in the room. The resistance of LDR is very high in darkness, which reduces to minimum when LDR is fully illuminated. LDR1 detects darkness, while LDR2 detects light in the morning. The circuit is designed around the popular timer IC NE555 (IC2), which is configured as a monostable. IC2 is activated by a low pulse applied to its trigger pin 2. Once triggered, output pin 3 of IC2 goeshigh and remains in that position until IC2 is triggered again at its pin 2. When LDR1 is illuminated with ambient light in the room, its resistance remains low, which keeps trigger pin 2 of IC2 at a positive potential. As a result, output pin 3 of IC2 goes low and the white LED remains off. As the illumination of LDR1’s sensitive window reduces, the resistance of the device increases.
In total darkness, the specified LDR has a resistance in excess of 280 kilo-ohms. When the resistance of LDR1 increases, a short pulse is applied to trigger pin 2 of IC2 via resistor R2 (150 kilo-ohms). This activates the monostable and its output goes high, causing the white LED to glow. Low-value capacitor C2 maintains the monostable for continuous operation, eliminating the timer effect. By increasing the value of C2, the ‘on’ time of the white LED can be adjusted to a predetermined time. LDR2 and associated components generate the morning alarm at dawn. LDR2 detects the ambient light in the room at sunrise and its resistance gradually falls and transistor T1 starts conducting. When T1 conducts, melody-generator IC UM66 (IC3) gets supply voltage from the emitter of T1 and it starts producing the melody. The musical tone generated by IC3 is amplified by single-transistor amplifier T2. Resistor R7 limits the current to IC3 is amplified by single-transistor amplifier T2. Resistor R7 limits the current to IC3 and zener diode ZD limits the voltage to a safer level of 3.3 volts.
The circuit can be easily assembled on a general-purpose PCB. Enclose it in a good-quality plastic case with provisions for LDR and LED. Use a reflective holder for white LED to get a spotlight effect for reading. Place LDRs away from the white LED, preferably on the backside of the case, to avoid unnecessary illumination. The speaker should be small so as to make the gadget compact. link
Wednesday, 10 April 2013
Clever Rain Alarm
Usually rain-alarms employ a single sensor. A serious draw-back of this type of sensor is that even if a single drop of water falls on the sensor, the alarm would sound. There is a probability that the alarm may be false. To overcome this draw-back, here we make use of four sensors, each placed well away from the other at suitable spots on the roof. The rain alarm would sound only if all the four sensors get wet. This reduces the probability of false alarm to a very great extent. The four rain-sensors SR1 to SR4, along with pull-up resistors R1 to R4 (connected to positive rails) and inverters N1 to N4, form the rain-sensor monitor stage. The sensor wires are brought to the PCB input points E1 to E5 using a 5-core cable. The four outputs of Schmitt inverter gates N1 to N4 go to the four inputs of Schmitt NAND gate N7, that makes the alarm driver stage.
Clever Rain-Alarm Circuit Diagram
When all four sensors sense the rain, all four inputs to gates N1 through N4 go low and their outputs go high. Thus all four in-puts to NAND gate N7 also go high and its output at pin 6 goes to logic 0. The out-put of gate N7 is high if any one or more of the rain-sensor plates SR1 through SR4 remain dry. The output of gate N7 is coupled to inverter gates N5 and N6. The output from gate N5 (logic 1 when rain is sensed) is brought to ‘EXT’ output connector, which may be used to control other external devices.
The output from the other inverter gate N6 is used as enable input for NAND gate N8, which is configured as a low-frequency oscillator to drive/modulate the piezo buzzer via transistor T1. The frequency of the oscillator/modulator stage is variable between 10 Hz and 200 Hz with the help of preset VR1. The buzzer is of piezo-electric type having a continuous tone that is inter-rupted by the low-frequency output of N8. The buzzer will sound whenever rain is sensed (by all four sensors). 6V power supply (100mA) is used here to enable proper interfacing of the CMOS and TTL ICs used in the circuit. The power supply requirement is quite low and a 6-volt battery pack can be easily used. During quiscent-state, only a negligible cur-rent is consumed by the circuit.
Even during active state, not more than 20mA current is needed for driving a good-quality piezo-buzzer. Please note that IC2, being of TTL type, needs a 5V regulated supply. There-fore zener D1, along with capacitor C2 and resistor R5, are used for this purpose.A parallel-track, general-purpose PCB or a veroboard is enough to hold all the components. The rain-sensors SR1 to SR4 can be fabricated as shown in the construction guide in Fig. 2. They can be made simply by connecting alternate parallel tracks using jumpers on the component side.
Use some epoxy cement on and around the wire joints at A and B to avoid corrosion. Also, the sensors can be cemented in place with epoxy cement. If the number of sensors is to be increased, just add another set of CD40106 and 7413 ICs along with the associated discrete components. Another good utility of the rain-alarm is in agriculture. When drip-irrigation is employed, fix the four sensors at four corners of the tree-pits, at a suit-able height from the ground. Then, as soon as the water rises to the sensor’s level, the circuit can be used to switch off the water pump.
Author : M.K. Chandra Mouleeswaran - Copyright: EFY
Tuesday, 9 April 2013
General Purpose Alarm
The alarm may be used for a variety of applications, such as frost monitor, room temperature monitor, and so on. In the quiescent state, the circuit draws a current of only a few microamperes, so that, in theory at least, a 9 V dry battery (PP3, 6AM6, MN1604, 6LR61) should last for up to ten years. Such a tiny current is not possible when ICs are used, and the circuit is therefore a discrete design. Every four seconds a measuring bridge, which actuates a Schmitt trigger, is switched on for 150 ms by a clock generator. In that period of 150 ms, the resistance of an NTC thermistor, R11, is compared with that of a fixed resistor. If the former is less than the latter, the alarm is set off.
When the circuit is switched on, capacitor C1 is not charged and transistors T1–T3 are off. After switch-on, C1 is charged gradually via R1, R7, and R8, until the base voltage of T1 exceeds the threshold bias. Transistor T1 then comes on and causes T2 and T3 to conduct also. Thereupon, C1 is charged via current source T1-T2-D1, until the current from the source becomes smaller than that flowing through R3 and T3 (about 3 µA). This results in T1 switching off, so that, owing to the coupling with C1, the entire circuit is disabled. Capacitor C1 is (almost) fully charged, so that the anode potential of D1 drops well below 0 V. Only when C1 is charged again can a new cycle begin.
When the circuit is switched on, capacitor C1 is not charged and transistors T1–T3 are off. After switch-on, C1 is charged gradually via R1, R7, and R8, until the base voltage of T1 exceeds the threshold bias. Transistor T1 then comes on and causes T2 and T3 to conduct also. Thereupon, C1 is charged via current source T1-T2-D1, until the current from the source becomes smaller than that flowing through R3 and T3 (about 3 µA). This results in T1 switching off, so that, owing to the coupling with C1, the entire circuit is disabled. Capacitor C1 is (almost) fully charged, so that the anode potential of D1 drops well below 0 V. Only when C1 is charged again can a new cycle begin.
General-Purpose Alarm Circuit diagram :
It is obvious that the larger part of the current is used for charging C1. Gate IC1a functions as impedance inverter and feedback stage, and regularly switches on measurement bridge R9–R12-C2-P1 briefly. The bridge is terminated in a differential amplifier, which, in spite of the tiny current (and the consequent small transconductance of the transistors) provides a large amplification and, therefore, a high sensitivity. Resistors R13 and R15 provide through a kind of hysteresis a Schmitt trigger input for the differential amplifier, which results in unambiguous and fast measurement results. Capacitor C2 compensates for the capacitive effect of long cables between sensor and circuit and so prevents false alarms.
If the sensor (R11) is built in the same enclosure as the remainder of the circuit (as, for instance, in a room temperature monitor), C2 and R13 may be omitted. In that case,C3 willabsorb any interference signals and so prevent false alarms. To prevent any residual charge in C3 causing a false alarm when the bridge is in equilibrium, the capacitor is discharged rapidly via D2 when this happens. Gates IC1c and IC1d form an oscillator to drive the buzzer (an a.c. type). Owing to the very high impedance of the clock, an epoxy resin (not pertinax) board must be used for building the alarm. For the same reason, C1 should be a type with very low leakage current. If operation of the alarm is required when the resistance of R11 is higher than that of the fixed resistor, reverse the connections of the elements of the bridge and thus effectively the inverting and non-inverting inputs of the differential amplifier.
An NTC thermistor such as R11 has a resistance at –18 °C that is about ten times as high as that at room temperature. It is, therefore, advisable, if not a must, when precise operation is required, to consult the data sheet of the device or take a number of test readings. For the present circuit, the resistance at –18 °C must be 300–400 kΩ. The value of R12 should be the same. Preset P1 provides fine adjustment of the response threshold. Note that although the prototype uses an NTC thermistor, a different kind of sensor may also be used, provided its electrical specification is known and suits the present circuit.
Source :http://www.ecircuitslab.com/2012/01/general-purpose-alarm.html
Sunday, 31 March 2013
Super Sensitive Intruder Alarm Circuit Using 741
Here is the description of the circuit diagram of an ultra sensitive intruder alarm. The shadow of an intruder passing few meters nearby the circuit is enough to trigger the alarm. The circuit is work based on the 741IC as the core of the system. This is the figure of the circuit.
Here IC2 uA 741 is wired as a sensitive comparator, whose set point is set by R6 &R7. The voltage divide by LDR and R9 is given at non inverting pin of IC2. The LDR can be housed in a dark tube to increase sensitivity. At standby mode these two voltages are set equal by adjusting R9.Now the out put (pin6) of comparator will be high. Transistor Q1 will be off. The voltage at trigger pin of IC1 will be positive and there will be no alarm. When there is an intruder near the LDR the shadow causes its resistance to increase. Now the voltages at the inputs of comparator will be different and the out put of IC2 will be low. This makes Q1 on. This makes a negative going pulse to trigger the IC1 which is wired as a mono stable multi vibrator. The out put of IC1 will be amplified by Q2 (SL 100) to produce alarm. The sensitivity is very important here. If you cannot adjust the required sensitivity properly, use one LOW resistance (~1K ) POT in series with R9 for fine adjustment. To setup the alarm, power up the circuit and adjust R9 so that LED D1 goes off.
Here IC2 uA 741 is wired as a sensitive comparator, whose set point is set by R6 &R7. The voltage divide by LDR and R9 is given at non inverting pin of IC2. The LDR can be housed in a dark tube to increase sensitivity. At standby mode these two voltages are set equal by adjusting R9.Now the out put (pin6) of comparator will be high. Transistor Q1 will be off. The voltage at trigger pin of IC1 will be positive and there will be no alarm. When there is an intruder near the LDR the shadow causes its resistance to increase. Now the voltages at the inputs of comparator will be different and the out put of IC2 will be low. This makes Q1 on. This makes a negative going pulse to trigger the IC1 which is wired as a mono stable multi vibrator. The out put of IC1 will be amplified by Q2 (SL 100) to produce alarm. The sensitivity is very important here. If you cannot adjust the required sensitivity properly, use one LOW resistance (~1K ) POT in series with R9 for fine adjustment. To setup the alarm, power up the circuit and adjust R9 so that LED D1 goes off.
Tuesday, 26 March 2013
Car Alarm Sound Booster
For car alarms, emphasis should be put on hearing the audible alert and identifying it as belonging to your wheels. Unfortunately, modern car alarm systems seem to have more or less the same alarm sound especially if they are from the same brand. Also, to comply with legal noise restrictions, the alarm sound is not always loud enough to be heard if the car is parked down the road.
Simple Car Alarm Sound Booster Circuit Diagram
The circuit shown here is designed to help boost the alarm sound by also activating the cars horn(s) when the alarm goes off. lnternally the car alarm system often provides a signal that activates the (optional) engine immobilizer and/or volume (ultrasound) sensors. This signal usually goes Low upon sys-tem triggering and high again when the alarm system is deactivated.
The alarm activation signal is fed to the circuit through Dl . When in idle state, T1 s gate is High and consequently the FET conducts, keeping power FET T2 firmly switched off. When the system gets an active low signal, T1 switches off allowing timing capacitor C2 to charge via R2. About 15 seconds later, when the voltage across C2 is high enough, T2 starts to conduct and relay RE1 is energized. This, in turn, provides the required path for the lights flashing signal to energize RE2 and feed battery power to the cars horn(s).
When the alarm system is turned off the activation signal returns to High. T1 starts to conduct and rapidly discharges C2 via R3. T2 is then cut off and REl is de-energized. Diode D2 suppresses back EMF from REl. The circuit draws less than 2 mA when idling. When activated the circuits current consumption is virtually that of the RE1 coil. RE1 is any simple SPST or SPDT relay, capable of switching about 0.5 A (at 12 V). The coil rating is for 12 VDC and a current requirement as low as you can find. Fuse F1 should be a slow blow type and rated about twice RE1s coil current.
The B5.170 in position T2 can sink a continuous current of about 0.5 A. However, a value of 1.2 A pulsed is specified by Fairchild for their devices. To keep the FETs d-s current due to C2 discharging within safe limits, R2 may be increased, C2 decreased and R3 increased, all proportionally. A factor of 2 will keep the FET out of harms way with maybe a slight change in the 15-second delay and the sensitivity of the circuit. C1 is used as a smoothing capacitor and F2 should be rated in accordance with the horn(s) maximum current draw.
Caution. The installation and use of this circuit may be subject to legal restrictions in your country, state or area.
Source: http://www.ecircuitslab.com/2012/06/simple-car-alarm-sound-booster.html
Sunday, 24 March 2013
Power Supply Failure Alarm
Most of the power supply failure indicator circuits need a separate power-supply for them-selves. But the alarm circuit presented here needs no additional supply source. It employs an electrolytic capacitor to store adequate charge, to feed power to the alarm circuit which sounds an alarm for a reasonable duration when the mains supply fails. During the presence of mains power supply, the rectified mains voltage is stepped down to a required low level.
Power Supply Failure Alarm Circuit Diagram
A zener is used to limit the filtered voltage to 15-volt level. Mains presence is indicated by an LED. The low-level DC is used for charging capacitor C3 and reverse biasing switching transistor T1. Thus, transistor T1 remains cut-off as long as the mains supply is present. As soon as the mains power fails, the charge stored in the capacitor acts as a power-supply source for transistor T1. Since, in the absence of mains supply, the base of transistor is pulled ‘low’ via resistor R8, it conducts and sounds the buzzer (alarm) to give a warning of the power-failure.
With the value of C3 as shown, a good-quality buzzer would sound for about a minute. By increasing or decreasing the value of capacitor C3, this time can be altered to serve one’s need. Assembly is quite easy. The values of the components are not critical. If the alarm circuit is powered from any external DC power-supply source, the mains supply section up to points ‘P’ and ‘M’can be omitted from the circuit.
Following points may be noted:
1. At a higher DC voltage level, transistor T1 (BC558) may pass some collector-to-emitter leakage current, causing a continuous murmuring sound from the buzzer. In that case, replace it with some low-gain transistor.
2. Piezo buzzer must be a continuous tone version, with built-in oscillator. To save space, one may use five small-sized 1000µF capacitors (in parallel) in place of bulky high-value capacitor C3.
Source :http://www.ecircuitslab.com/2011/11/power-supply-failure-alarm.html
Subscribe to:
Posts (Atom)
