Friday, 6 June 2014
Wideband Wien Oscillator Circuit with Single Gang Pot
This Wien bridge oscillator (after Max Wien, 1866–1938) produces a low-distortion sine wave of constant amplitude, from about 15 Hz to 150 kHz. It requires just four opamps and will work off a single 9-volt battery. Also, unlike most Wien bridge oscillators, it does not require a dual-gang potentiometer for tuning. Op amp IC2b provides an artificial ground so that the circuit will operate from a unipolar supply (9 V battery or power pack). IC2a is the main amplifier for the oscillator. The frequency range is divided into four decades by 2-pole, 4-way rotary switch SW1.
Wideband Wien Oscillator Circuit with Single-Gang Pot Circuit Diagram
Only one arm of the Wien network is varied, but the change in positive feedback that would normally result is compensated for by IC1b, which works to bootstrap R2, thereby changing the negative feedback enough to maintain oscillation. A linear change in the resistance of the tuning pot results in a roughly logarithmic change in frequency. To get a more conventional linear change a log-taper pot is used wired so that rotating the knob anticlockwise causes frequency to increase.
You could use an anti-log pot the other way around if you prefer, but these things are notoriously hard to find. IC1A is an integrator that monitors the amplitude of the output signal and drives an LED (D2). This must be mounted facing the LDR (light dependent resistor) and shielded from ambient light (for example, with a piece of heat-shrink tubing). IC1a is then able to control the gain of IC2a so that oscillation is maintained with minimum distortion.
The maximum output amplitude of the generator is about 2 Vp-p when the LED and LDR are mounted as close as possible. Distortion is less than 0.5 % in the lowest range, and too low for the author to measure in the higher ranges. Any LDR should work, provided its dark resistance is greater than 100 kO. If you do not have an LDR with such high resistance, try increasing R5 until oscillation starts. Breadboarded prototypes of the circuit were built by the author using dual and quad opamp packages, and both work equally well.
Wideband Wien Oscillator Circuit with Single-Gang Pot Circuit Diagram
Only one arm of the Wien network is varied, but the change in positive feedback that would normally result is compensated for by IC1b, which works to bootstrap R2, thereby changing the negative feedback enough to maintain oscillation. A linear change in the resistance of the tuning pot results in a roughly logarithmic change in frequency. To get a more conventional linear change a log-taper pot is used wired so that rotating the knob anticlockwise causes frequency to increase.
You could use an anti-log pot the other way around if you prefer, but these things are notoriously hard to find. IC1A is an integrator that monitors the amplitude of the output signal and drives an LED (D2). This must be mounted facing the LDR (light dependent resistor) and shielded from ambient light (for example, with a piece of heat-shrink tubing). IC1a is then able to control the gain of IC2a so that oscillation is maintained with minimum distortion.
The maximum output amplitude of the generator is about 2 Vp-p when the LED and LDR are mounted as close as possible. Distortion is less than 0.5 % in the lowest range, and too low for the author to measure in the higher ranges. Any LDR should work, provided its dark resistance is greater than 100 kO. If you do not have an LDR with such high resistance, try increasing R5 until oscillation starts. Breadboarded prototypes of the circuit were built by the author using dual and quad opamp packages, and both work equally well.
Author: Merlin Blencowe (Elektor)
Resistors:
R1,R2,R3,R6,R10,R11 = 10kO
R7 = 100kO
R4,R9,R12 = 100O
R5 = 12kO
R8 = 1kO
P1,P2 = 10kO potentiometer, logarithmic law
R13 = LDR, R(dark) >100kO, e.g. Excelitas Tech type
VT90N1 (Newark/Farnell # 2568243)
Capacitors:
C1,C5 = 1µF solid
C2,C6 = 100nF
C3,C7 = 10nF
C4,C8 = 1nF
C9-C12 = 47µF 16V, electrolytic, radial
Semiconductors:
D1,D2,D3 = 1N4148
D4 = LED, red, 5mm
IC1,IC2 = TL072ACP
Miscellaneous:
SW1 = 2-pole 4-position rotary switch, C&K Compo-
nents type RTAP42S04WFLSS
K1,K2 = PCB terminal block, 5mm pitch
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment
Note: only a member of this blog may post a comment.