Showing posts with label telephone. Show all posts
Showing posts with label telephone. Show all posts
Friday, 5 April 2013
Telephone call Voice Changer
Voice manipulation device specially intended for props, 9V Battery operation
Although this kind of voice effect can be obtained by means of some audio computer programs, a few correspondents required a stand-alone device, featuring microphone input and line or loudspeaker outputs. This design fulfills these requirements by means of a variable gain microphone preamplifier built around IC1A, a variable steep Wien-bridge pass-band filter centered at about 1KHz provided by IC1B and an audio amplifier chip (IC2) driving the loudspeaker.
Parts:P1______________10K Log. Potentiometer
R1,R10__________10K 1/4W Resistors
R2_______________1K 1/4W Resistor
R3______________50K 1/2W Trimmer Cermet or Carbon
R4,R6,R7,R14___100K 1/4W Resistors
R5______________47K 1/4W Resistor
R8______________68K 1/4W Resistor
R9_______________2K2 1/2W Trimmer Cermet or Carbon
R11_____________33K 1/4W Resistor
R12_____________18K 1/4W Resistor
R13_____________15K 1/4W Resistor
C1,C2,C3,C8,C9_100nF 63V Polyester Capacitors
C4______________10µF 25V Electrolytic Capacitor
C5_____________220nF 63V Polyester Capacitor (Optional, see Notes)
C6_______________4n7 63V Polyester Capacitor
C7______________10nF 63V Polyester Capacitor
C10____________220µF 25V Electrolytic Capacitor
IC1___________LM358 Low Power Dual Op-amp
IC2_________TDA7052 Audio power amplifier IC
MIC1__________Miniature electret microphone
SPKR______________8 Ohm Small Loudspeaker
SW1____________DPDT Toggle or Slide Switch
SW2,SW3________SPST Toggle or Slide Switches
J1____________6.3mm or 3mm Mono Jack socket
B1_______________9V PP3 Battery (See Notes) Clip for PP3 Battery
Notes:
- The pass-band filter can be bypassed by means of SW1A and B: in this case, a non-manipulated microphone signal will be directly available at the line or loudspeaker outputs after some amplification through IC1A.
- R3 sets the gain of the microphone preamp. Besides setting the microphone gain, this control can be of some utility in adding some amount of distortion to the signal, thus allowing a more realistic imitation of a telephone call voice.
- R9 is the steep control of the pass-band filter. It should be used with care, in order to avoid excessive ringing when filter steepness is approaching maximum value.
- P1 is the volume control and SW2 will switch off amplifier and loudspeaker if desired.
- C5 is optional: it will produce a further band reduction. Some people think the resulting effect is more realistic if this capacitor is added.
- If the use of an external, moving-coil microphone is required, R1 must be omitted, thus fitting a suitable input jack.
- This circuit was intended to be powered by a 9V PP3 battery, but any dc power supply in the 6 - 12V range can be used successfully.
Tuesday, 26 March 2013
FM Telephone Bug Circuit
Here is a simple transmitter that when connected to a phone line, will transmit anything on that line (execpt the dial tone) to any FM radio. The frequency can be tuned from 88 to about 94Mhz and the range is about 200 feet. It is extremely easy to build and is therefore a good, useful beginner project.
FM Telephone Bug Circuit diagram:
Parts:
R1 180 Ohm 1/4 W Resistor
R2 12K 1/4 W Resistor
C1 330pF Capacitor
C2 12pF Capacitor
C3 471pF Capacitor
C4 22pF Capacitor
Q1 2SA933 Transistor
D1, D2, D3, D4 1SS119 Silicon Diode
D5 Red LED
S1 SPDT Switch
L1 Tuning Coil
MISC Wire, Circuit Board
Notes :
1. L1 is 7 turns of 22 AWG wire wound on a 9/64 drill bit. You may need to experiment with the number of turns.
2. By stretching and compressing the coils of L1, you can change the frequency of the transmitter. The min frequency is about 88 Mhz, while the max frequency is around 94 Mhz.
3. The green wire from the phone line goes to IN1. The red wire from the phone line goes to IN2. The green wire from OUT1 goes to the phone(s), as well as the red wire from OUT2.
4. The antenna is a piece of thin (22 AWG) wire about 5 inches long.
5. All capacitors are rated for 250V or greater.
6. The transmitter is powered by the phone line and is on only when the phone is in use. S1 can be used to turn the transmitter off if it is not needed.
7. If you have problems with the LED burning out, then add a 300 ohm 1/4W resistor in series with it.
FM Telephone Bug Circuit diagram:
R1 180 Ohm 1/4 W Resistor
R2 12K 1/4 W Resistor
C1 330pF Capacitor
C2 12pF Capacitor
C3 471pF Capacitor
C4 22pF Capacitor
Q1 2SA933 Transistor
D1, D2, D3, D4 1SS119 Silicon Diode
D5 Red LED
S1 SPDT Switch
L1 Tuning Coil
MISC Wire, Circuit Board
Notes :
1. L1 is 7 turns of 22 AWG wire wound on a 9/64 drill bit. You may need to experiment with the number of turns.
2. By stretching and compressing the coils of L1, you can change the frequency of the transmitter. The min frequency is about 88 Mhz, while the max frequency is around 94 Mhz.
3. The green wire from the phone line goes to IN1. The red wire from the phone line goes to IN2. The green wire from OUT1 goes to the phone(s), as well as the red wire from OUT2.
4. The antenna is a piece of thin (22 AWG) wire about 5 inches long.
5. All capacitors are rated for 250V or greater.
6. The transmitter is powered by the phone line and is on only when the phone is in use. S1 can be used to turn the transmitter off if it is not needed.
7. If you have problems with the LED burning out, then add a 300 ohm 1/4W resistor in series with it.
Source : http://www.ecircuitslab.com/2011/06/fm-telephone-bug-circuit.html
Subscribe to:
Posts (Atom)
