Identify diagram: low

Showing posts with label low. Show all posts

Tuesday, 9 April 2013

A Low Distortion Audio Pre amplifier

In an audio amplifier the quality of sound depends upon a number of factors, e.g. quality of active and passive components, circuit configuration, and layout. To an extent, the selection of components depends on the constructor’s budget. The discrete active components like transistors have been increasingly replaced by linear ICs, making the task of designer easier. With the passage of time, the general-purpose op-amps like LM741, which were being used in audio/hi-fi circuits, have become The preamplifier circuit presented here is based on a dual precision op-amp for the construction of a low distortion, high quality audio preamplifier.

Low Distortion Audio Pre-amplifier Circuit diagram:

A dual op-amp OPA2604 from Burr-Brown is used for all the stages. The FET input stage op-amp was chosen in this context it is worthwile to mention another popular bi-polar architecture op-amp, the NE5534A. It has, no doubt, an exceptionally low noise figure of 4nV/ÖHz but rest of the specifications compared to OPA2604 are virtually absent in this IC. Also This IC is also capable of operating at higher voltage rails of ± 24V (max.). Also its input bias current (100 pA) is many orders lower than its bipolar counterpart’s. This ensures a multifold reduction in noise.

A channel seperation of 142 dB exists between In the circuit, buffer is essential for the proper working of the subsequent blocks. A nominal input impedance of 47k is offered by this stage which prevents overloading of the preamplifier. The tone control is a baxandall type filter circuit.The bandwidth limiter is basically a low-pass filter with an upper cut-off ceiling at the end of the useful audio spectrum. The gain at 10 kHz is approximately 17 dB. The design is essentially 3-pole type and the upper frequency is set at 25 kHz. This lSetting the unit is fairly simple. Check the power leads feeding the IC for symmetrical voltages. High quality audio output from the line output socket is to be fed as the input signal to this preamplifier. Output of the preamplifier is fed to the power a The whole circuit consumes about 10 mA when the above-mentioned ICs are used. Power supply requirements are not critical as the circuit works on 7.5V to 15V DC..

Source : http://www.ecircuitslab.com/2012/01/low-distortion-audio-pre-amplifier.html

Wednesday, 3 April 2013

A Low Cost Hearing Aid Circuit

Small and portable unit, Useful for old men and old women

This low-cost, general-purpose electronic hearing aid works off 3V DC (2x1.5V battery). The circuit can be easily assembled on a veroboard. For easy assembling and maintenance, use an 8-pin DIP IC socket for TDA2822M.

Circuit Diagrams:

A Low Cost hearing Aid Circuit

Parts:

P1 = 10K
R1 = 2.2K
R2 = 330K
R3 = 680R
R4 = 33R
R5 = 100R
R6 = 4.7R
R7 = 4.7R
R8 = 220R
C1 = 0.01uF-10V
C2 = 100nF-63V
C3 = 47uF-10V
C4 = 10uF-10V
C5 = 0.01uF-10V
C6 = 100uF-10V
C7 = 100nF-63V
C8 = 100nF-63V
D1 = Red LED
Q1 = BC547
IC1 = TDA2822M
EP1 = Mono Earphone 32R
SW1 = On-Off Switch

Circuit Operation:

In this circuit, transistor Q1 and associated components form the audio signal preamplifier for the acoustic signals picked up by the condenser microphone and converted into corresponding electrical signals. Resistor R5 and capacitor C3 decouple the power supply of the preamplifier stage. Resistor R1 biases the internal circuit of the low-voltage condenser microphone for proper working. The audio output from the preamplifier stage is fed to the input of the medium-power amplifier circuit via capacitor C2 and volume control P1.

The medium-power amplifier section is wired around popular audio amplifier IC TDA2822M (not TDA2822). This IC, specially designed for portable low-power applications, is readily available in 8-pin mini DIP package. Here the IC is wired in bridge configuration to drive the 32-ohm general-purpose monophonic earphone. Red LED (D1) indicates the power status. Resistor R8 limits the operating current of D1. The audio output of this circuit is 10 to 15mW and the quiescent current drain is below 1 mA.

Source : www.electronsforu.com